Finding mold or water damage in your bathroom is something that no homeowner wants to deal with, but the fact is that this happens more often than most people realize and that preventing it is much easier than dealing with the discovery later on after you have neglected this very important room of your home. If you are moving into a brand new house, then you are in luck, since there will probably be neither water damage nor mold in the bathroom when you get into it. You are ahead of the game. If you are moving into an old house or have lived in the same home for a number of years, then you might have some issues on your hands, but hopefully the room is not so far gone that you will have to renovate completely to take care of them.
The first thing that you need to look at in your bathroom is the floor. This is what holds up everything else in the room and if it gives way, it does not matter the quality of the craftsmanship in the rest of the room; everything in the room will end up on the ground under the house. So, if the flooring in your bathroom is old or damaged, then you should replace it. Before you put the new flooring down, though, you should take a look at the joists underneath to see if they are water damaged or rotting. If they feel weak in any way, you should find the money to repair it with, since building a new bathroom on top of weak joists makes no sense at all, because weak and rotted joists are what you are trying to prevent in the first place. You should also look for mold under the old flooring, as well, and remove any materials contaminated with it.
After you replace the flooring (if necessary) and put down the new flooring, you need to make sure that the entire floor is water tight to prevent rotting the joists later on. Much more water goes through the bathroom every day than you may realize, so think about this when waterproofing your floor. There should be no missing areas of grout or caulking anywhere in the room.
The next place you need to look is up. Does your ceiling sag at all or is it cracked in any places? Do you have a window in the bathroom or an exhaust vent? Or do you have neither? One of the most important things that you can install in the bathroom to protect it is an exhaust vent. Steam from your shower or bath is absorbed by the ceiling over time if it has nowhere to go, cause mold growth, and the drywall to sag. If enough water is absorbed by the ceiling over the years, it can crack and eventually collapse.
Jim Corkern is a writer and respected contributor to the Water damage restoration and mold remediation Industry. Visit his sites for more information.
http://www.localrestoration.com and
http://www.moldrestorationusa.com
Saturday, September 29, 2007
Bathroom Water Damage and Mold Help
Nobody wants to find mold growing in the bathroom, but you will if you do not take the proper steps to make sure that it is taken care of on a regular basis. There are a number of things that you can do to stop mold from growing in your bathroom and since you will spend a large amount of time in this room over the years, it is suggested that you take these steps no matter what it might cost your wallet. The last thing you want is to need a mold remediation done in the bathroom that could cost you thousands of dollars simply because you did not take the time and effort to care for it.
One of the most important parts of your bathroom is not the tub, the toilet, or the sink, but the floor. This holds up everything else in the room and if this goes, the entire thing will fall to the ground underneath the house. This happens more often than you think and it is usually due to floors not being properly waterproofed. You can do this by making sure that there are no cracked tiles or cracked portions of linoleum or whatever flooring you have decided to have put down in the bathroom. If the flooring is old and you have not had it replaced since you have lived in the home and it is damaged, you will want to seriously consider having the floor checked out to see if it is water damaged. Mold can also start growing underneath it, so if the bathroom smells musty at all, you may want to have the house checked for this, too.
Another thing that you want to consider adding to the room is an exhaust vent. Exhaust vents are required by many local building codes and you may not really feel like you need it if you have a window, but installing one is a good investment since it is not always a good idea to leave the bathroom window open. The reason for these vents is so steam is not absorbed by the ceiling and upper walls and cause them to become molded over time. Ceilings that absorb water like this will also start to sag and possibly collapse later.
You should also keep an eye on the plumbing underneath the sink and near the toilet. You should not neglect the slow drips that can happen with these pipes and you should get them fixed as soon as possible, no matter how water tight your floor might be.
Jim Corkern is a writer and promoter of quality
water damage restoration companies and
mold remediation companies across the united states.
One of the most important parts of your bathroom is not the tub, the toilet, or the sink, but the floor. This holds up everything else in the room and if this goes, the entire thing will fall to the ground underneath the house. This happens more often than you think and it is usually due to floors not being properly waterproofed. You can do this by making sure that there are no cracked tiles or cracked portions of linoleum or whatever flooring you have decided to have put down in the bathroom. If the flooring is old and you have not had it replaced since you have lived in the home and it is damaged, you will want to seriously consider having the floor checked out to see if it is water damaged. Mold can also start growing underneath it, so if the bathroom smells musty at all, you may want to have the house checked for this, too.
Another thing that you want to consider adding to the room is an exhaust vent. Exhaust vents are required by many local building codes and you may not really feel like you need it if you have a window, but installing one is a good investment since it is not always a good idea to leave the bathroom window open. The reason for these vents is so steam is not absorbed by the ceiling and upper walls and cause them to become molded over time. Ceilings that absorb water like this will also start to sag and possibly collapse later.
You should also keep an eye on the plumbing underneath the sink and near the toilet. You should not neglect the slow drips that can happen with these pipes and you should get them fixed as soon as possible, no matter how water tight your floor might be.
Jim Corkern is a writer and promoter of quality
water damage restoration companies and
mold remediation companies across the united states.
Issues When Hiring a Contractor
Hiring a contractor to build your new house or remodel it may be one of the most important decisions that you will ever make, so it needs to be done right the first time. There are a few things that anyone considering having a home built for them need to know before even beginning to search for the contractor that will be in their life for many months to come.
The first thing you need to know about hiring a contractor is the fact that this person will be a constant part of your life for the next few months or however long it takes to complete the house. You need to be able to get along with this person and stand to be around them. Talk with them not only on the phone, but also in person to really get an idea of who they are and what they are all about. Talking to them in person will give you the benefit of a gut feeling about whether you will get along with them or not.
The second thing is that you need to find out if the contractor that you are interested in is licensed or not. Their license should be current and there should be no claims made against it.
You also need to find out if the contractor you want to hire is properly insured and that he or she will allow you to have copies of their insurance policies. This will give you the peace of mind that if any of the crew is injured while working on your home, you are not liable in any way, since they will be on your property.
You also need to be prepared to talk to some of the contractor’s past clients to get an idea of what quality their work is. You will want to ask whether there have been any mold or water damage issues with the property since it was built.
Another issue you may face with your contractor if you are not having an entire home built, but simply a renovation or remodeling in one or two rooms, is the fact that the contractor and his crew will be in and out of your house. You will want to sit down with your spouse and figure out exactly when the work day will begin for the crew and what time it will end. Having small children in the house during the project is not a great idea, so you may want to have the children somewhere else during this time.
Jim Corkern is a writer and promoter of quality
water damage restoration and
mold remediation companies across the united states.
The first thing you need to know about hiring a contractor is the fact that this person will be a constant part of your life for the next few months or however long it takes to complete the house. You need to be able to get along with this person and stand to be around them. Talk with them not only on the phone, but also in person to really get an idea of who they are and what they are all about. Talking to them in person will give you the benefit of a gut feeling about whether you will get along with them or not.
The second thing is that you need to find out if the contractor that you are interested in is licensed or not. Their license should be current and there should be no claims made against it.
You also need to find out if the contractor you want to hire is properly insured and that he or she will allow you to have copies of their insurance policies. This will give you the peace of mind that if any of the crew is injured while working on your home, you are not liable in any way, since they will be on your property.
You also need to be prepared to talk to some of the contractor’s past clients to get an idea of what quality their work is. You will want to ask whether there have been any mold or water damage issues with the property since it was built.
Another issue you may face with your contractor if you are not having an entire home built, but simply a renovation or remodeling in one or two rooms, is the fact that the contractor and his crew will be in and out of your house. You will want to sit down with your spouse and figure out exactly when the work day will begin for the crew and what time it will end. Having small children in the house during the project is not a great idea, so you may want to have the children somewhere else during this time.
Jim Corkern is a writer and promoter of quality
water damage restoration and
mold remediation companies across the united states.
Heating Devices Can Cause Fires
There is not a homeowner in the world that wants to have to clean up after a house fire, but this is a common occurrence around the world, no matter how careful you might be. You can go through your whole life and never even see a single tiny grease fire in the kitchen and your house still burn to the ground. On the same token, you can have several small fires on your stove or in other parts of your house, and the entire thing still be standing tall when you are ninety years old. But, do not think that it all comes down to luck, because it most certainly does not. The likelihood of a fire burning your house down is directly related to how closely you pay attention to the electrical items in your home. This includes maintenance on large appliances and whether you are using small electrical appliances correctly or not.
One thing that most people do not think about causing a house fire is a curling iron. These have been used by women to curl their hair for many years, but leaving an electric one on and unattended for any period of time is not a good idea. They can cause not only burns on any small children or pets that may run into the cord, but can also cause things to catch on fire depending on where you are using it in the house.
Another item that needs to be used carefully is the space heater. These come in all shapes and sizes, but the general consensus is to never leave these on for extended periods of time and to not use extension cords with them. If you have to use an extension cord, make sure that it is a heavy gauge one with a marking of at least 14. If you can stand to turn them off while you are sleeping, it is a good idea to do so, since many fires of this nature happen at night when no one is awake to watch the heater.
A winter item that you need to be just as careful with is the electric blanket. There have been reports of people waking up with their beds on fire because they left them on while they were sleeping. You also do not want to put pressure on the heating elements in these blankets, since they are easily damaged.
Jim Corkern is a writer and promoter of quality
Mold Remediation and
water damage restoration companies across the united states.
One thing that most people do not think about causing a house fire is a curling iron. These have been used by women to curl their hair for many years, but leaving an electric one on and unattended for any period of time is not a good idea. They can cause not only burns on any small children or pets that may run into the cord, but can also cause things to catch on fire depending on where you are using it in the house.
Another item that needs to be used carefully is the space heater. These come in all shapes and sizes, but the general consensus is to never leave these on for extended periods of time and to not use extension cords with them. If you have to use an extension cord, make sure that it is a heavy gauge one with a marking of at least 14. If you can stand to turn them off while you are sleeping, it is a good idea to do so, since many fires of this nature happen at night when no one is awake to watch the heater.
A winter item that you need to be just as careful with is the electric blanket. There have been reports of people waking up with their beds on fire because they left them on while they were sleeping. You also do not want to put pressure on the heating elements in these blankets, since they are easily damaged.
Jim Corkern is a writer and promoter of quality
Mold Remediation and
water damage restoration companies across the united states.
Friday, September 7, 2007
Areas At Risk For Mold
If you own a home, then you have probably gone through your home looking for mold on at least one occasion and if you have not, then you really should think about doing this sometime soon. We have all heard about toxic mold on the news in one form or another and how harmful it can be to our health, but this is not the only issue with mold. Even if you manage to kill it, it can still cause allergic reactions in some people because the spores are still airborne and our bodies still recognize them as something they need to defend themselves against. Taking some antihistamine medication can help, but no one wants to take allergy medicine all the time if you really do not have to.
There are a number of signs that will show you that you should look for mold in different areas of your house, but you may not exactly know what you are supposed to be looking for. Go around your house and any room that is inherently moist should be scrutinized closely. Unless you have done a remodeling job recently and you have completely waterproofed the bathroom, then you should consider it as a possible breeding ground for mold. Other rooms that are inherently moist are the kitchen, laundry room, and the basement.
You should look for signs of moisture in the laundry room since it is likely to stay humid due to the amount of wet clothing and evaporating of water that stays in there all the time. Your dryer needs to be properly vented to the outside if it is not already, unless it is a ventless model. Always wash wet clothes as soon as possible and do not put dry clothes on top of them. You will most likely forget about them and they will mold after about 48 hours.
Your kitchen is another area that you should be concerned with. Areas around the sink and floor that are not waterproofed and even the ceiling should be suspect. The steam that comes off the stove when you cook damages the ceiling and can discolor it over time, so you should have an exhaust fan installed over the stove to help prevent this. These fans should also be put in other moist rooms of the house, especially the bathroom. This will keep you from having to repaint the ceiling as often as you would normally have to and even keep you from having to replace drywall.
New York flood water damage restoration
South Carolina mold remediation
There are a number of signs that will show you that you should look for mold in different areas of your house, but you may not exactly know what you are supposed to be looking for. Go around your house and any room that is inherently moist should be scrutinized closely. Unless you have done a remodeling job recently and you have completely waterproofed the bathroom, then you should consider it as a possible breeding ground for mold. Other rooms that are inherently moist are the kitchen, laundry room, and the basement.
You should look for signs of moisture in the laundry room since it is likely to stay humid due to the amount of wet clothing and evaporating of water that stays in there all the time. Your dryer needs to be properly vented to the outside if it is not already, unless it is a ventless model. Always wash wet clothes as soon as possible and do not put dry clothes on top of them. You will most likely forget about them and they will mold after about 48 hours.
Your kitchen is another area that you should be concerned with. Areas around the sink and floor that are not waterproofed and even the ceiling should be suspect. The steam that comes off the stove when you cook damages the ceiling and can discolor it over time, so you should have an exhaust fan installed over the stove to help prevent this. These fans should also be put in other moist rooms of the house, especially the bathroom. This will keep you from having to repaint the ceiling as often as you would normally have to and even keep you from having to replace drywall.
New York flood water damage restoration
South Carolina mold remediation
What You Need When Removing Mold
Nobody wants to have to remove the mold from their home, but if you live in an older house, then you may have to go through this eventually. Even newly built homes can have mold growing in them in certain areas if bad techniques were used or just poor quality materials. As long as the building codes in your area were followed by the contractor of your new house, there is nothing that you can do, even if the poor quality materials are the reason that mold exists. If the job was done “by the book”, then you cannot obtain any legal compensation. When having a home built for you, make sure you know that the contractor you hired to do it will do the job with good quality building materials and get references before even letting them start.
But, what do you do if you already have mold in the house? Well, you can probably clean up a lot of it yourself if you have a smaller mold problem. If you have experience in interior remodeling work, then you can tackle even a larger scale mold removal project on your own. Your insurance may even cover it, if it is due to another kind of damage that your homeowner’s insurance covers, like water leaks.
There is a certain amount of equipment that you will need if you are going to do this job on your own, though. Having a respirator is something that you will really need, especially if you are going to open up any walls. You can get a basic respirator from a hardware store, but if you are going to open up any walls, you will probably want a respirator that has a HEPA filter attached to it.
You will also want a few heavy duty trash bags to toss the debris in.
As far as some protective equipment that you can wear, heavy duty rubber gloves might also be helpful depending on what you are handling. If you are just scrubbing floors or walls, then you could probably get away with some lighter latex gloves. Some plastic disposable coveralls and covers for your shoes will help keep mold spores from getting on your clothes. Safety glasses might also be necessary.
As with your respirator, the cleanup job after all the debris is gone should be done with a vacuum that has a HEPA filter on it. This will release clean, filtered air back into your home instead of releasing the dust and mold spores like a normal vacuum would.
Black mold removalfrom drywall
Water Damage Restoration Discussion Group
But, what do you do if you already have mold in the house? Well, you can probably clean up a lot of it yourself if you have a smaller mold problem. If you have experience in interior remodeling work, then you can tackle even a larger scale mold removal project on your own. Your insurance may even cover it, if it is due to another kind of damage that your homeowner’s insurance covers, like water leaks.
There is a certain amount of equipment that you will need if you are going to do this job on your own, though. Having a respirator is something that you will really need, especially if you are going to open up any walls. You can get a basic respirator from a hardware store, but if you are going to open up any walls, you will probably want a respirator that has a HEPA filter attached to it.
You will also want a few heavy duty trash bags to toss the debris in.
As far as some protective equipment that you can wear, heavy duty rubber gloves might also be helpful depending on what you are handling. If you are just scrubbing floors or walls, then you could probably get away with some lighter latex gloves. Some plastic disposable coveralls and covers for your shoes will help keep mold spores from getting on your clothes. Safety glasses might also be necessary.
As with your respirator, the cleanup job after all the debris is gone should be done with a vacuum that has a HEPA filter on it. This will release clean, filtered air back into your home instead of releasing the dust and mold spores like a normal vacuum would.
Black mold removalfrom drywall
Water Damage Restoration Discussion Group
Taking Care of Your Sewage Damaged Home
One of the nastiest things you may ever have to do to your home is clean up the sewage left behind by a flood. You can have a professional cleaning service do this for you, but you should really be able to do this on your own unless for some reason you are physically unable or you get sick very easily. The money that you will save by doing it yourself will be substantial and this is money that you can use to purchase new clothing, furniture, or anything else you may need in the days, weeks, and months following the flood. Having the right information to help you with this is crucial, though.
The worst thing about this is that flood waters are usually contaminated with bacteria, viruses, hazardous chemicals, and sometimes even decaying bodies. Wearing protective equipment while you are in this process is essential to keep yourself from getting sick, so purchase whatever you need to. Latex gloves, disposable coveralls, and disposable foot covers are necessary. You do not want to wear porous clothing while you are doing this, because it will soak right through to your skin. A roll of duct tape should also be bought to seal up the gaps around your ankles and wrists.
Depending on whether you have someone else helping you take care of the other sewage damaged areas of the house, you will need two or more buckets. You need to keep this at an even number, because one will be used as a rinse bucket and the other will have the cleaning solution in it.
Unfortunately, you will probably not be able to save most of the upholstered furniture in your home because the padding will soak up so much of the soil, sewage, and bacteria. You can save items with small amounts of padding that can be replaced, like dining room chairs, and even take this as an opportunity to put a new pattern of fabric on them. Carpets will also probably need to be thrown away and the padding underneath them certainly will be.
Once the padding and carpet has been taken up if it was necessary in the area you are in, you should have a mop or some other cleaning utensil to use. Dip it into the cleaning solution and begin scrubbing the floor with it. Rinse it in the other bucket thoroughly before putting it back into the cleaning bucket. Do not contaminate your bucket filled with cleaner. After you get done scrubbing the whole room, you should go back over it with a disinfectant for a little extra assurance.
Austin Water Damage Restoration
Ft.Worth Water Damage Restoration
The worst thing about this is that flood waters are usually contaminated with bacteria, viruses, hazardous chemicals, and sometimes even decaying bodies. Wearing protective equipment while you are in this process is essential to keep yourself from getting sick, so purchase whatever you need to. Latex gloves, disposable coveralls, and disposable foot covers are necessary. You do not want to wear porous clothing while you are doing this, because it will soak right through to your skin. A roll of duct tape should also be bought to seal up the gaps around your ankles and wrists.
Depending on whether you have someone else helping you take care of the other sewage damaged areas of the house, you will need two or more buckets. You need to keep this at an even number, because one will be used as a rinse bucket and the other will have the cleaning solution in it.
Unfortunately, you will probably not be able to save most of the upholstered furniture in your home because the padding will soak up so much of the soil, sewage, and bacteria. You can save items with small amounts of padding that can be replaced, like dining room chairs, and even take this as an opportunity to put a new pattern of fabric on them. Carpets will also probably need to be thrown away and the padding underneath them certainly will be.
Once the padding and carpet has been taken up if it was necessary in the area you are in, you should have a mop or some other cleaning utensil to use. Dip it into the cleaning solution and begin scrubbing the floor with it. Rinse it in the other bucket thoroughly before putting it back into the cleaning bucket. Do not contaminate your bucket filled with cleaner. After you get done scrubbing the whole room, you should go back over it with a disinfectant for a little extra assurance.
Austin Water Damage Restoration
Ft.Worth Water Damage Restoration
Little known Phone Sticker Squeals On Water Damage And Voids Warranty
If you take a look inside the case of your cell phone, you should see a round white sticker placed somewhere on the device. What is it? This is called a water damage sticker and if your phone is exposed to moisture that makes its way inside the phone, this can be used to completely void your warranty, no matter the reason your phone may stop working. It does not seem to take much, either; a simple drop of water placed onto this sticker is enough to change its color and void the warranty on your cell phone. For honest consumers who accidentally get a small bit of water on their phone and then 5 or 6 months later, suddenly notice that the phone is having problems, knowing about this sticker is quite useful.
What exactly can you do to stop this little devil from voiding the warranty on your phone should is accidentally get a little damp? The best thing that you can do is to take a piece of satin finished scotch tape and put it over the sticker to keep the color from changing if it gets wet. If you drop your phone into the toilet or the bathtub, this probably isn’t going to be that effective, but if you are just worried about general moisture problems or an accidental quick spill of something on the phone, this should work just fine. If your phone stops working for some other reason, remove the tape and take it back to the manufacturer for repairs or a replacement.
It is was not exactly a bad idea for these stickers to be put on the inside of phones, though; a lot of phones get returned that are supposedly not water damaged, but are. At the same time, though, it is bad for the consumer because having such a sticker can completely void the warranty regardless of whether the liquid was the reason the phone stopped working or not. The phone could have just been a defective model and it would make no difference.
Hopefully people will use the information presented here honestly and not try to defraud the phone company into giving them a new item after their phone was irreparably damaged by having a hot cup of coffee spilled onto it or something like that. For honest consumers just having a bit of bad luck, it is great to know these kinds of things about our electronics just in case. Unfortunately, there are those that will attempt to misuse this information.
Information provided by: Miami Residential Water Damage Restoration Contractors and
Orlando water Damage
What exactly can you do to stop this little devil from voiding the warranty on your phone should is accidentally get a little damp? The best thing that you can do is to take a piece of satin finished scotch tape and put it over the sticker to keep the color from changing if it gets wet. If you drop your phone into the toilet or the bathtub, this probably isn’t going to be that effective, but if you are just worried about general moisture problems or an accidental quick spill of something on the phone, this should work just fine. If your phone stops working for some other reason, remove the tape and take it back to the manufacturer for repairs or a replacement.
It is was not exactly a bad idea for these stickers to be put on the inside of phones, though; a lot of phones get returned that are supposedly not water damaged, but are. At the same time, though, it is bad for the consumer because having such a sticker can completely void the warranty regardless of whether the liquid was the reason the phone stopped working or not. The phone could have just been a defective model and it would make no difference.
Hopefully people will use the information presented here honestly and not try to defraud the phone company into giving them a new item after their phone was irreparably damaged by having a hot cup of coffee spilled onto it or something like that. For honest consumers just having a bit of bad luck, it is great to know these kinds of things about our electronics just in case. Unfortunately, there are those that will attempt to misuse this information.
Information provided by: Miami Residential Water Damage Restoration Contractors and
Orlando water Damage
A General Facts Guide About Mold
Whether you are indoors or outdoors, mold is always there. No matter where you are, there is no such thing as an environment on the planet earth that is considered to be mold-free. Wherever there are the three things that mold need to survive, there will be mold, even though you might not be able to see it. Mold is only visible to the human eye when colonies of it start to grow. Just what does mold need to grow?
Mold needs nutrients. In an outdoor environment, this would be organic matter such as dead plants or animals. This is a necessary natural event that has to take place to get rid of the some of the debris that builds up on the forest floor. In the indoor environment, molds often feed on building materials. These can include cardboard, paper on both the sides of drywall, soap, fabrics, and other kinds of dust.
Moisture is also required by mold in order to survive. In order to begin decaying organic matter and digesting it, it needs moisture. Mold often grows inside the home during the summer when moisture becomes trapped inside the house and in the house in the winter when certain areas become drafty and condensation builds up in areas.
Something else mold needs to survive is very simple and we all have a lot of it, whether we realize it or not. Mold needs time to grow. It can start to form a colony as soon as 24 hours up to ten days after it gets enough of the nutrients and moisture that it needs to survive. The longer you allow something such as a wet towel or wet piece of clothing to lie on the floor in the back of your closet, the more time you are giving mold to start growing on it.
One last thing that molds tend to need in order to continue growing is heat. Not all molds need a significant amount of heat in order to grow, but many do. Molds have been known to survive at extreme temperatures and remain dormant, but not actually continue growing. They can be exposed to temperatures around 2 degrees Celsius and still only become dormant instead of dying like some other organisms would do.
Information provided by: New York water damage restoration contractors
Connecticut mold remediation and water damage restoration
Mold needs nutrients. In an outdoor environment, this would be organic matter such as dead plants or animals. This is a necessary natural event that has to take place to get rid of the some of the debris that builds up on the forest floor. In the indoor environment, molds often feed on building materials. These can include cardboard, paper on both the sides of drywall, soap, fabrics, and other kinds of dust.
Moisture is also required by mold in order to survive. In order to begin decaying organic matter and digesting it, it needs moisture. Mold often grows inside the home during the summer when moisture becomes trapped inside the house and in the house in the winter when certain areas become drafty and condensation builds up in areas.
Something else mold needs to survive is very simple and we all have a lot of it, whether we realize it or not. Mold needs time to grow. It can start to form a colony as soon as 24 hours up to ten days after it gets enough of the nutrients and moisture that it needs to survive. The longer you allow something such as a wet towel or wet piece of clothing to lie on the floor in the back of your closet, the more time you are giving mold to start growing on it.
One last thing that molds tend to need in order to continue growing is heat. Not all molds need a significant amount of heat in order to grow, but many do. Molds have been known to survive at extreme temperatures and remain dormant, but not actually continue growing. They can be exposed to temperatures around 2 degrees Celsius and still only become dormant instead of dying like some other organisms would do.
Information provided by: New York water damage restoration contractors
Connecticut mold remediation and water damage restoration
Subscribe to:
Posts (Atom)
