If your cell phone has been submersed in water recently and you have managed to save it yourself, then good for you. But, there are some other tips that you might want to know just in case.
Another method for helping the phone dry out (if you do not have any rice on hand) is to put it on top of the vent on a monitor or a television for at least 24 hours. The low amount of heat put out by these devices should be enough to gently dry out the phone.
If you are the kind of person who keeps the silica packs that come packed in electronics, coats, shoes, and etcetera, you can put the phone into a plastic bag with a couple of these and let them absorb the moisture over a couple of days. If you do not have these on hand, a local craft store should have a flower drying kit that will contain a silica sand-type mixture. Put it in a Tupperware dish, use a dryer sheet, lay the phone on top of it, and seal it.
Corrosion is a definite threat to cell phones and other electronics and some people have suggested that you wash the phone in distilled water to wash away any kind of minerals that might have existed in the water or other liquid the phone was originally submersed in. If you choose to try this, do it only after you have removed the SIM card and battery.
If the battery is wet, do NOT heat it to try and dry it out. Batteries, especially lithium-ion ones, are quite sensitive and they very well may explode if you try to speed up the drying process in this manner.
If you choose to use alcohol to clean off parts of the phone that are sticky with soda or another similar liquid, do not apply heat to the device in any way. Do not reattach the battery until the smell of alcohol is completely gone.
This might also seem like common sense, but do not put any electronic device into the microwave. You will probably destroy not only your device, but even your microwave could be put at risk.
You should be aware that most phone warranties do not cover water damaged phones and that most phones today have special stickers inside them (only one visible to you) that will tell a technician if the phone has come into contact with water or even just too much humidity. Be careful when taking your phone outdoors when humidity is very high. It is possible to void your warranty.
Wednesday, January 23, 2008
Things You Should Know About Water Damage And Your Computer
Water or almost any other kind of liquid is not a great thing to have around your computer or any other electronic device. This kind of damage can be expensive to either replace or to have repaired and unfortunately, many people who are unfortunate enough to have this happen to them cannot afford it.
If the liquid spilled upon the device is acidic, like soda or coffee, then it generally does more damage than simple water would do. It causes more corrosion to the metal areas of the motherboard or any other computer component such as the hard drive or CD-ROM.
One of the worst case scenarios is that you spill a liquid onto your laptop where everything, motherboard, hard drive, CD-ROM, and etcetera are all packed into the same general area. In most cases of water damage to computers, the liquid is spilled merely on the keyboard or another outside component such as the mouse. With laptops, spilling a liquid on the keyboard does not mean that only the keyboard is affected, but also the other components sharing the shell of the laptop are, as well. What can you do if water or another liquid is spilled on your laptop?
Unplug it from the A/C adapter and remove the battery IMMEDIATELY. Unplug any other external devices including external hard drives, mice, other input devices, CD-ROMs, DVD-ROMs, and etcetera. The next thing is to turn the laptop completely upside down to stop the liquid from sinking any further into it.
Use a towel or paper towels to clean up the spilled liquid, wipe off the keyboard, exterior, and any external devices that came into contact with the liquid as well.
At this point, you could do one of two things. You could take it to a professional repairman and have them look at it (I hope you have an extra arm and leg lying around) or if you know how to take something apart and put it back together, you can try to fix it yourself. In trying to fix it, you may irreparably damage it, so if you are even remotely unsure about your ability to repair it, it is better to take it to a professional.
If you choose the do-it-yourself route, disassemble the computer and allow it to dry out completely for at least 24 hours, if not longer. Let it dry until you are satisfied that it is completely done. Whatever you do, do not turn the power on before it is. It is not water itself that kills the circuit board of any electronic device, but the electricity that runs through it when someone tries to turn the device on when it is still wet.
If it was just water, drying should be all it needs. If it was soda or any other acidic liquid, clean it with rubbing alcohol and Q-tips, then put it back together and wait for the alcohol to dry. See if it works.
If the liquid spilled upon the device is acidic, like soda or coffee, then it generally does more damage than simple water would do. It causes more corrosion to the metal areas of the motherboard or any other computer component such as the hard drive or CD-ROM.
One of the worst case scenarios is that you spill a liquid onto your laptop where everything, motherboard, hard drive, CD-ROM, and etcetera are all packed into the same general area. In most cases of water damage to computers, the liquid is spilled merely on the keyboard or another outside component such as the mouse. With laptops, spilling a liquid on the keyboard does not mean that only the keyboard is affected, but also the other components sharing the shell of the laptop are, as well. What can you do if water or another liquid is spilled on your laptop?
Unplug it from the A/C adapter and remove the battery IMMEDIATELY. Unplug any other external devices including external hard drives, mice, other input devices, CD-ROMs, DVD-ROMs, and etcetera. The next thing is to turn the laptop completely upside down to stop the liquid from sinking any further into it.
Use a towel or paper towels to clean up the spilled liquid, wipe off the keyboard, exterior, and any external devices that came into contact with the liquid as well.
At this point, you could do one of two things. You could take it to a professional repairman and have them look at it (I hope you have an extra arm and leg lying around) or if you know how to take something apart and put it back together, you can try to fix it yourself. In trying to fix it, you may irreparably damage it, so if you are even remotely unsure about your ability to repair it, it is better to take it to a professional.
If you choose the do-it-yourself route, disassemble the computer and allow it to dry out completely for at least 24 hours, if not longer. Let it dry until you are satisfied that it is completely done. Whatever you do, do not turn the power on before it is. It is not water itself that kills the circuit board of any electronic device, but the electricity that runs through it when someone tries to turn the device on when it is still wet.
If it was just water, drying should be all it needs. If it was soda or any other acidic liquid, clean it with rubbing alcohol and Q-tips, then put it back together and wait for the alcohol to dry. See if it works.
Water And Your Cell Phone Do Not Mix
Many people have horror stories about how they lost anywhere between $50 and $600 on replacing a cell phone that was dropped into the toilet or the bath tub or any other liquid. The sad fact is that most cell phone warranties do not cover water damage and unfortunately, cell phone manufacturers have begun to place what some are calling “snitch stickers” in their phones that change color if they have been exposed to even a drop of water. While this keeps people trying to get a new free phone from saying that their old phone was not water damaged when it actually was, it is unfortunate for the consumer because these stickers have been known to change color in even just high humidity. So, water damage to phones is a serious problem, but what do you do if your phone does become submersed?
Take it out of the water immediately. The plastic covers on most cell phones these days are pretty tight, but water can get inside the phone. As long as you get the phone out of the water in under around 20 seconds, it should not have that much opportunity to seep in.
After you do that, remove the battery and do not hesitate. This is to effectively cut the power supply off from your phone; electricity and water combined are what fries your phone, not just the water itself.
If your phone has a SIM card, remove that quickly, as well. These cards store contact and other kinds of data from the phone and to some people, the information held on that card could be more valuable than the phone itself, even if the phone might cost them $600. Some service providers, however, do not use SIM cards, like Verizon Wireless.
Do not put the battery or the SIM card back into the phone. Dry them separately. Then, dry the phone itself from the outside and then if possible, put it in a bowl of rice and let it stay there overnight. You might get a grain of rice or two in your phone, but this probably will not happen. Rice will help draw out the moisture. Wait at least two or three days before trying to turn your phone back on. Never turn on an electronic device after it has been wet until you are sure it has completely dried out.
As long as the phone looks dry, it should be safe to try and turn the phone on. If it doesn’t work with the battery, try plugging it into the wall outlet. If this works, you just need to replace the battery.
Take it out of the water immediately. The plastic covers on most cell phones these days are pretty tight, but water can get inside the phone. As long as you get the phone out of the water in under around 20 seconds, it should not have that much opportunity to seep in.
After you do that, remove the battery and do not hesitate. This is to effectively cut the power supply off from your phone; electricity and water combined are what fries your phone, not just the water itself.
If your phone has a SIM card, remove that quickly, as well. These cards store contact and other kinds of data from the phone and to some people, the information held on that card could be more valuable than the phone itself, even if the phone might cost them $600. Some service providers, however, do not use SIM cards, like Verizon Wireless.
Do not put the battery or the SIM card back into the phone. Dry them separately. Then, dry the phone itself from the outside and then if possible, put it in a bowl of rice and let it stay there overnight. You might get a grain of rice or two in your phone, but this probably will not happen. Rice will help draw out the moisture. Wait at least two or three days before trying to turn your phone back on. Never turn on an electronic device after it has been wet until you are sure it has completely dried out.
As long as the phone looks dry, it should be safe to try and turn the phone on. If it doesn’t work with the battery, try plugging it into the wall outlet. If this works, you just need to replace the battery.
Mold Legislation Before Congress To Help Americans With Mold Problems
In March of 2003, Congressman John Conyers Jr. out of Michigan introduced a bill to Congress called the United States Toxic Mold Safety and Protection Act.
This Bill says that the Centers for Disease Control and the Environmental Protection agency will be responsible for examining the effects of different kinds of mold on the health of human beings and they will research and develop more accurate results of the serious problems that are presented by the presence of mold in human habitats.
This Bill will also direct the Department of Housing and Urban Development and the Environmental Protection Agency to establish a certain number of items that will constitute the conditions that will cause mold to grow indoors and will outline what can be done in order to inhibit this growth. These guidelines will not only address the causes of mold growth and what can be done to prevent it, but also the inspection, testing, and remediation techniques.
The Bill also says that you could receive tax credits for the inspection and/or removal and remediation of any mold in the home or business.
Grants will be given for the removal of mold in any and all buildings accessible by the public.
It also will create what it calls a National Toxic Mold Insurance Program that will be administered by FEMA (the Federal Emergency Management Agency) in order to protect home and business owners from any crippling financial losses, because most insurance companies do not provide insurance for mold at all or what they do provide is inadequate.
It will also necessitate the modification of building codes in local areas in order to keep the risk of mold infections in newly built homes and other buildings down.
This bill will also require mold inspections for apartment complexes and any other multi-unit residential property. Public housing is also subject to these mandatory mold inspections.
Victims of mold health complications will also be covered by Medicaid if they do not have any other health care in place at the time.
It has also authorized the establishment of different public information programs that will educate the public about the hazards of mold that is allowed to grow indoors. It is believed that an educated public is better prepared to defend itself against these hazards.
For more information, please visit http://www.house.gov/conyers/mold.htm . If you support this bill, please contact your congressman.
This Bill says that the Centers for Disease Control and the Environmental Protection agency will be responsible for examining the effects of different kinds of mold on the health of human beings and they will research and develop more accurate results of the serious problems that are presented by the presence of mold in human habitats.
This Bill will also direct the Department of Housing and Urban Development and the Environmental Protection Agency to establish a certain number of items that will constitute the conditions that will cause mold to grow indoors and will outline what can be done in order to inhibit this growth. These guidelines will not only address the causes of mold growth and what can be done to prevent it, but also the inspection, testing, and remediation techniques.
The Bill also says that you could receive tax credits for the inspection and/or removal and remediation of any mold in the home or business.
Grants will be given for the removal of mold in any and all buildings accessible by the public.
It also will create what it calls a National Toxic Mold Insurance Program that will be administered by FEMA (the Federal Emergency Management Agency) in order to protect home and business owners from any crippling financial losses, because most insurance companies do not provide insurance for mold at all or what they do provide is inadequate.
It will also necessitate the modification of building codes in local areas in order to keep the risk of mold infections in newly built homes and other buildings down.
This bill will also require mold inspections for apartment complexes and any other multi-unit residential property. Public housing is also subject to these mandatory mold inspections.
Victims of mold health complications will also be covered by Medicaid if they do not have any other health care in place at the time.
It has also authorized the establishment of different public information programs that will educate the public about the hazards of mold that is allowed to grow indoors. It is believed that an educated public is better prepared to defend itself against these hazards.
For more information, please visit http://www.house.gov/conyers/mold.htm . If you support this bill, please contact your congressman.
Fixing A Water Damaged Laptop
You might not it, but the circuit board in your laptop and any other electronic items in your house were rinsed in clean water and dried before they were put into use? As long as the water is clean, the device will not be irreparably damaged. If something is allowed to soak in dirty water, however, with different particles and other mineral content, then the device will become damaged.
If you have a laptop that has gotten wet, the first thing to do is to turn it off immediately and remove all sources of power from it including the A/C adapter and batteries. Set these aside while you take the laptop and turn it upside down. This will stop any more liquid from seeping further into the computer.
After you do that, use paper towels or a rag to mop up the liquid that was spilled, wipe the liquid off the keyboard and the outside. Also wipe down anything else electronic nearby that got wet, too, like an external CD-ROM or external hard drive.
Disassemble the laptop (take a look at your user’s manual, too) and allow the insides to air out for at least a full day. Most people who have gone through this procedure recommend longer, especially if the liquid got further down into the computer. The best thing to do is let it sit and dry until you are confident that the interior is completely moisture-free.
If the only liquid it came into contact with was water out of your faucet, then allowing it to dry should be all that is necessary, but if it was something like soda, tea, or coffee that was spilled onto it, then you will want to clean it with some rubbing alcohol. You can use cotton swabs for this. Do not apply any heat to the device while you are cleaning it with alcohol and wait until the smell of alcohol is completely gone before you try to power it up.
Put the device back together after you are finished letting it dry or cleaning it up. Reattach the battery and see if it powers on. If it does, wait and see if it starts up as it should. If it does not, then attach the A/C adapter and plug it up. If you can turn the device on after trying this, then all you should need is a new battery. This should be pretty easy to obtain, as long as you have the money to purchase it with, either from the manufacturer or from a site like eBay.
If you have a laptop that has gotten wet, the first thing to do is to turn it off immediately and remove all sources of power from it including the A/C adapter and batteries. Set these aside while you take the laptop and turn it upside down. This will stop any more liquid from seeping further into the computer.
After you do that, use paper towels or a rag to mop up the liquid that was spilled, wipe the liquid off the keyboard and the outside. Also wipe down anything else electronic nearby that got wet, too, like an external CD-ROM or external hard drive.
Disassemble the laptop (take a look at your user’s manual, too) and allow the insides to air out for at least a full day. Most people who have gone through this procedure recommend longer, especially if the liquid got further down into the computer. The best thing to do is let it sit and dry until you are confident that the interior is completely moisture-free.
If the only liquid it came into contact with was water out of your faucet, then allowing it to dry should be all that is necessary, but if it was something like soda, tea, or coffee that was spilled onto it, then you will want to clean it with some rubbing alcohol. You can use cotton swabs for this. Do not apply any heat to the device while you are cleaning it with alcohol and wait until the smell of alcohol is completely gone before you try to power it up.
Put the device back together after you are finished letting it dry or cleaning it up. Reattach the battery and see if it powers on. If it does, wait and see if it starts up as it should. If it does not, then attach the A/C adapter and plug it up. If you can turn the device on after trying this, then all you should need is a new battery. This should be pretty easy to obtain, as long as you have the money to purchase it with, either from the manufacturer or from a site like eBay.
The Three Ways Mold Affects Us
Mold has been around since before us and has been having an effect on us since the time of Moses, yet we have only recently begun to see the true effects of mold on the human body. Mold not only affects the human body, but also the bodies of animals, such as our dogs, cats, and even our birds. We have become aware that mold is not something that we want living where we do, but a lot of us do not feel that there is much that we can do about it. Most molds fit into three different categories and are classified according to what kind of effect they have on us and our health.
Molds that are considered toxic produce what are called mycotoxins and even though these molds rarely occur where we live, they can cause all kinds of health complications and some of these can lead to death in the most serious of circumstances. Penicilliosis is native to the region of Southeast Asia and has a fairly high mortality rate without treatment, but even with treatment the number of deaths total about one in five. Another serious occurrence associated with mold is called aspergilloma and it happens when fungus begins to grow in balls inside any cavities existing in the body, particularly the lungs. Stachybotrys mold produces mycotoxins and is the most famous of the different black molds that exist and has been referenced by the media as “toxic black mold”.
Allergenic molds seem to affect people the most often and as their name implies, they usually cause some common allergy symptoms, but can be quite a nuisance. They can aggravate existing allergies or asthma, making the symptoms that a person already has become worse over time. Anti-histamines may help a small amount, but getting rid of the contamination is usually the only way to keep the symptoms from returning.
Pathogenic molds are less rare than toxic molds or allergenic molds, but they can be just as dangerous in people that have compromised immune systems such as those who are HIV-positive or has AIDS, cancer, or is recovering from surgery of any kind. The elderly, pets, and small children are also more at risk than a normal healthy adult person would be.
If you believe that mold exists in your home, you should perform some do-it-yourself mold tests and when you get the results back, hire a professional to get rid of the infestation as soon as possible.
Molds that are considered toxic produce what are called mycotoxins and even though these molds rarely occur where we live, they can cause all kinds of health complications and some of these can lead to death in the most serious of circumstances. Penicilliosis is native to the region of Southeast Asia and has a fairly high mortality rate without treatment, but even with treatment the number of deaths total about one in five. Another serious occurrence associated with mold is called aspergilloma and it happens when fungus begins to grow in balls inside any cavities existing in the body, particularly the lungs. Stachybotrys mold produces mycotoxins and is the most famous of the different black molds that exist and has been referenced by the media as “toxic black mold”.
Allergenic molds seem to affect people the most often and as their name implies, they usually cause some common allergy symptoms, but can be quite a nuisance. They can aggravate existing allergies or asthma, making the symptoms that a person already has become worse over time. Anti-histamines may help a small amount, but getting rid of the contamination is usually the only way to keep the symptoms from returning.
Pathogenic molds are less rare than toxic molds or allergenic molds, but they can be just as dangerous in people that have compromised immune systems such as those who are HIV-positive or has AIDS, cancer, or is recovering from surgery of any kind. The elderly, pets, and small children are also more at risk than a normal healthy adult person would be.
If you believe that mold exists in your home, you should perform some do-it-yourself mold tests and when you get the results back, hire a professional to get rid of the infestation as soon as possible.
The Dangers Of Mold, What You Should Know About Mold
A lot of people, including insurance companies, would like you to think that mold isn’t as dangerous to your health as all the media hype would have you believe, but actually mold is just as harmful as people say that it is. Mold has been around longer than human beings have, but that doesn’t mean that it doesn’t cause us problems both medically and financially. If anyone tries to tell you that mold isn’t going to cause any damage to your health, you might want to tell them some of the things that mold has been known to do.
Mold has been known to cause an excess amount of fatigue, sinusitis, allergy symptoms, and damaged vision. The allergy symptoms are one of the most common results and it can occur either in the form of a runny nose, sneezing, watery eyes, or even skin rashes that are unsightly and tend to be very itchy. If you do not experience any of these symptoms while you are outside of your home, it might be mold or something else in your living environment that is causing you to have these reactions. Either way, you should probably see a doctor as soon as you are able to determine that something in your home is causing you to have these symptoms.
It has been known to kill our pets and cause lung bleeding, especially in infants. Elderly people, particularly those in poor health or with any respiratory problems, are at risk for the health effects of mold. Anyone who is HIV-positive, have AIDS, or those who are in the process of recovering from surgery are also at a high risk for mold-related infections and health complications.
Some of the most dangerous infections in the world are caused by mold and in the region of Southeast Asia, this includes a condition that affects mostly HIV-positive and AIDS patients called penicilliosis. It is caused by a mold in the genus penicillium, a genus which is most famous for including the species of mold responsible for the “miracle drug” penicillin that was invented back in the 1940’s.
There are actually a lot of things that you can do to make your home and workplace mold-free. Taping a do-it-yourself home mold test to the grill of one of your air conditioning vents is a good idea; it will test to see if your air conditioner is responsible for spreading the mold around your house. Putting tests in other rooms after you’ve stirred up the air for a few minutes with a house fan is also a good way to test for mold. If you see mold growing visibly on your wall, use rubber gloves and scrape a small bit off onto the test and send it to a mold laboratory.
Mold has been known to cause an excess amount of fatigue, sinusitis, allergy symptoms, and damaged vision. The allergy symptoms are one of the most common results and it can occur either in the form of a runny nose, sneezing, watery eyes, or even skin rashes that are unsightly and tend to be very itchy. If you do not experience any of these symptoms while you are outside of your home, it might be mold or something else in your living environment that is causing you to have these reactions. Either way, you should probably see a doctor as soon as you are able to determine that something in your home is causing you to have these symptoms.
It has been known to kill our pets and cause lung bleeding, especially in infants. Elderly people, particularly those in poor health or with any respiratory problems, are at risk for the health effects of mold. Anyone who is HIV-positive, have AIDS, or those who are in the process of recovering from surgery are also at a high risk for mold-related infections and health complications.
Some of the most dangerous infections in the world are caused by mold and in the region of Southeast Asia, this includes a condition that affects mostly HIV-positive and AIDS patients called penicilliosis. It is caused by a mold in the genus penicillium, a genus which is most famous for including the species of mold responsible for the “miracle drug” penicillin that was invented back in the 1940’s.
There are actually a lot of things that you can do to make your home and workplace mold-free. Taping a do-it-yourself home mold test to the grill of one of your air conditioning vents is a good idea; it will test to see if your air conditioner is responsible for spreading the mold around your house. Putting tests in other rooms after you’ve stirred up the air for a few minutes with a house fan is also a good way to test for mold. If you see mold growing visibly on your wall, use rubber gloves and scrape a small bit off onto the test and send it to a mold laboratory.
Mold In Your Refrigerator And What To Do About It
If there is one thing that most people cannot stand, it is when you open the refrigerator and find that a jar of something you need at that moment such as mayonnaise or jelly has become contaminated with mold. Sometimes it is green or white and it grows either on the food itself or on the inside of the jar’s lid and you do not notice it is there until you are already scooping it out and putting it onto your bread. Yuck! A whole jar has just been wasted because of mold.
What about the other food near that jar? You should check to see if any other food in your refrigerator is contaminated with mold and throw it away immediately, especially if it is something that does not come in a jar. Leftovers, fruit, or vegetables that we often end up shoving into the back of the fridge and forgetting about are common mold hotspots in our refrigerators. Maybe you made too much food one night and you just have not had a taste for the leftovers or maybe you just have not gotten around to throwing it away.
Cleaning out your refrigerator of old and outdated items is one of the best ways to prevent mold from starting to grow inside your refrigerator. Wasting food is a bad thing to do no matter where you are and if you have any leftovers that have not been eaten up to around 48 hours after you originally prepared it, it is probably a good idea to get some Ziploc bags or Tupperware dishes and put this excess food in the freezer to eat at a later date.
Do not leave the vegetables or fruit in the plastic bags that you put them in when you pick them up from the produce section at your grocery store. This traps moisture inside the bag and it will cause your food to rot and eventually become moldy.
Any cracked eggs in the carton need to be removed. You should not buy a carton of eggs if any of the eggs appear to be cracked open; bacteria on the outside of the egg can get inside and begin to multiply.
Cheese is also a favorite food of mold in the refrigerator and if you see mold growing on a block of cheese (do not try to save individually wrapped slices), take a knife and cut an inch around the moldy spot and throw it away. Do not touch the mold with the knife and wash it immediately after.
What about the other food near that jar? You should check to see if any other food in your refrigerator is contaminated with mold and throw it away immediately, especially if it is something that does not come in a jar. Leftovers, fruit, or vegetables that we often end up shoving into the back of the fridge and forgetting about are common mold hotspots in our refrigerators. Maybe you made too much food one night and you just have not had a taste for the leftovers or maybe you just have not gotten around to throwing it away.
Cleaning out your refrigerator of old and outdated items is one of the best ways to prevent mold from starting to grow inside your refrigerator. Wasting food is a bad thing to do no matter where you are and if you have any leftovers that have not been eaten up to around 48 hours after you originally prepared it, it is probably a good idea to get some Ziploc bags or Tupperware dishes and put this excess food in the freezer to eat at a later date.
Do not leave the vegetables or fruit in the plastic bags that you put them in when you pick them up from the produce section at your grocery store. This traps moisture inside the bag and it will cause your food to rot and eventually become moldy.
Any cracked eggs in the carton need to be removed. You should not buy a carton of eggs if any of the eggs appear to be cracked open; bacteria on the outside of the egg can get inside and begin to multiply.
Cheese is also a favorite food of mold in the refrigerator and if you see mold growing on a block of cheese (do not try to save individually wrapped slices), take a knife and cut an inch around the moldy spot and throw it away. Do not touch the mold with the knife and wash it immediately after.
Mold In The Time Of Moses
If your insurance adjuster claims that mold has been around for many years longer than we have and that it does not to the damage that the media and health community say that it does, then perhaps something you should have them read up on is a verse that comes straight out of the Bible and blatantly talks about homes that are diseased.
It is called a “leprous plague” in the scripture Leviticus 14:34; it appears growing on the walls and if a family went to the priest and said “my house is diseased”, it was ordered that the people leave the house so the priest could go in and examine it. If it was determined to be diseased, then the stones of the house were to be removed and taken to a place that was away from town and from where people resided so that others would be safe from the plague. Stones were brought in to replace the ones that were removed and it was watched to see if the mold returned; if it did return, the entire house was torn down and all the debris was taken to where the first stones were dumped.
Mold was serious business in Biblical times just as it is today, but back then there were no formal antibiotics or fungicides to help get rid of the mold either in the body or on a person’s property, so most of the time it simply had to be torn down and replaced. Even the deaths of the firstborns of Egypt are sometimes attributed by scholars to the presence of mold on the food that was stored underground after the locusts came. If the food was contaminated with almost any mold, especially Stachybotrys atra, it is speculated that it would have been what killed all the firstborn children in Egypt at the time because during that period, it was customary for the eldest Egyptian child in a family to receive a second portion of food. Food that has been stored underground, especially if it was stored directly on top of the soil, would have been a perfect food also for mold. The Jews alive at the time would not have suffered from this plague because they ate herbs, lamb, and unleavened bread, which should have been safe from any mold contamination.
So, do not let your insurance adjuster fool you by trying to downplay the seriousness of mold. It was serious over 2,000 years ago and it is just as serious today.
It is called a “leprous plague” in the scripture Leviticus 14:34; it appears growing on the walls and if a family went to the priest and said “my house is diseased”, it was ordered that the people leave the house so the priest could go in and examine it. If it was determined to be diseased, then the stones of the house were to be removed and taken to a place that was away from town and from where people resided so that others would be safe from the plague. Stones were brought in to replace the ones that were removed and it was watched to see if the mold returned; if it did return, the entire house was torn down and all the debris was taken to where the first stones were dumped.
Mold was serious business in Biblical times just as it is today, but back then there were no formal antibiotics or fungicides to help get rid of the mold either in the body or on a person’s property, so most of the time it simply had to be torn down and replaced. Even the deaths of the firstborns of Egypt are sometimes attributed by scholars to the presence of mold on the food that was stored underground after the locusts came. If the food was contaminated with almost any mold, especially Stachybotrys atra, it is speculated that it would have been what killed all the firstborn children in Egypt at the time because during that period, it was customary for the eldest Egyptian child in a family to receive a second portion of food. Food that has been stored underground, especially if it was stored directly on top of the soil, would have been a perfect food also for mold. The Jews alive at the time would not have suffered from this plague because they ate herbs, lamb, and unleavened bread, which should have been safe from any mold contamination.
So, do not let your insurance adjuster fool you by trying to downplay the seriousness of mold. It was serious over 2,000 years ago and it is just as serious today.
How To Keep Mold Out Of Your Life And Off Of Your Property
Mold gets onto just about everything that we own at some point or another; it is whether or not the mold starts to actually grow on the item and stay there that tends to be the problem. Whether it is clothes, furniture, walls, floors, clothes, or food, mold can do quite a lot of damage to the things in our home and we cannot always see it coming. Even the items that we need to be clean the most, like our baby’s bottles that they drink their milk and juice out of.
The bottles that we have today are not just the cylinders that they used to be; sometimes they come in strange shapes that are hard to get completely dry and when this happens and they are put back into the refrigerator, they can often become moldy. How can you prevent this? All you have to do after you wash them is dry them inside the best that you can and then simply put them in the freezer until you are ready to use them again. Mold does not like these temperatures and this will inhibit any growth. It is a popular thing to put kitchen staples like flour, sugar, and cornmeal into the freezer to protect them from bugs and mice, so why not use this to your advantage to prevent mold, as well?
Mold also likes to grow on clothes that have been forgotten about in the backs of closets. Try not to pack your closets so full of clothes that air cannot circulate. The clothes being packed so close together creates the warmth that the mold needs to survive and if your house is humid enough, the moisture it needs is also there. The last thing mold needs to live is food and your clothing is more than enough to supply that need. It might also be a good idea to install a vent into the closet to help air circulate a little better, too.
Something else that causes mold to grow is when you throw damp and dirty clothing into a bathroom closet and leave it there. This is particularly a bad idea if you have carpet in it. Carpet in the bathroom is a bad idea all by itself, but when you couple it with dirty, wet clothes or towels, you are asking for a mold infestation to start in the back of your closet. The solution for this is to use a plastic laundry hamper and to empty it regularly, which should be around every day and a half. Mold usually starts to grow after about 48 hours.
The bottles that we have today are not just the cylinders that they used to be; sometimes they come in strange shapes that are hard to get completely dry and when this happens and they are put back into the refrigerator, they can often become moldy. How can you prevent this? All you have to do after you wash them is dry them inside the best that you can and then simply put them in the freezer until you are ready to use them again. Mold does not like these temperatures and this will inhibit any growth. It is a popular thing to put kitchen staples like flour, sugar, and cornmeal into the freezer to protect them from bugs and mice, so why not use this to your advantage to prevent mold, as well?
Mold also likes to grow on clothes that have been forgotten about in the backs of closets. Try not to pack your closets so full of clothes that air cannot circulate. The clothes being packed so close together creates the warmth that the mold needs to survive and if your house is humid enough, the moisture it needs is also there. The last thing mold needs to live is food and your clothing is more than enough to supply that need. It might also be a good idea to install a vent into the closet to help air circulate a little better, too.
Something else that causes mold to grow is when you throw damp and dirty clothing into a bathroom closet and leave it there. This is particularly a bad idea if you have carpet in it. Carpet in the bathroom is a bad idea all by itself, but when you couple it with dirty, wet clothes or towels, you are asking for a mold infestation to start in the back of your closet. The solution for this is to use a plastic laundry hamper and to empty it regularly, which should be around every day and a half. Mold usually starts to grow after about 48 hours.
Important Steps On How To Avoid Water Damage To Your Home
Water damage is one of the worst things that can happen to your home that you can almost completely prevent, unless it is caused by mother nature. Floods and hurricanes are something that we can’t really prevent; all we can do is just try to prepare for it and often our preparations aren’t good enough. We should not feel bad about this, however, because nature will almost always win over any preparations that we make to try and keep her out of our homes. There are a few things that you can do to prevent water damage to your home on a smaller scale, but you will have to be diligent in your efforts if you are truly going to make it work.
Pay attention to your water heater. This and anything else in your house that uses a large amount of water is at risk of leaking out onto the floor and doing some serious damage. It should always be installed on the lowest level of your home, preferably in the basement raised up off the floor and sitting on a drain pan that is connected to a water drain in the floor. This will make sure that even if your water heater does start to leak, the water goes back into the sewer or your septic tank instead of onto your floor.
If you are worried about your dishwasher leaking, check the pipes and hoses that are leading to it first and make sure they are connected tightly and are not cracked anywhere. If you are buying a home that comes with a dishwasher already installed, you will want to check around the base of it to check for water damage. If the floor around it is discolored or if the base of the cabinet near it is warped, you might have a leaky dishwasher.
One thing that most homeowners have to do at least once a year is cleaning out the gutters that run around the roof and drain the water from the roof, through the downspout, and away from the house. These always end up collecting leaves, sticks, and other debris and if the gutters become clogged with this material, it will cause water to simply drop off the roof to the base of your house. If water saturates the ground at your home’s foundation, it will eventually cause it to sink into the ground.
Pay attention to your water heater. This and anything else in your house that uses a large amount of water is at risk of leaking out onto the floor and doing some serious damage. It should always be installed on the lowest level of your home, preferably in the basement raised up off the floor and sitting on a drain pan that is connected to a water drain in the floor. This will make sure that even if your water heater does start to leak, the water goes back into the sewer or your septic tank instead of onto your floor.
If you are worried about your dishwasher leaking, check the pipes and hoses that are leading to it first and make sure they are connected tightly and are not cracked anywhere. If you are buying a home that comes with a dishwasher already installed, you will want to check around the base of it to check for water damage. If the floor around it is discolored or if the base of the cabinet near it is warped, you might have a leaky dishwasher.
One thing that most homeowners have to do at least once a year is cleaning out the gutters that run around the roof and drain the water from the roof, through the downspout, and away from the house. These always end up collecting leaves, sticks, and other debris and if the gutters become clogged with this material, it will cause water to simply drop off the roof to the base of your house. If water saturates the ground at your home’s foundation, it will eventually cause it to sink into the ground.
Employer Concerns About Mold And The Options
One of the places that we don’t usually think of when we think of mold is our working environment. We usually think that we’ll find it in our homes, but other buildings are just as susceptible. If you are responsible for a number of employees and you suspect that there might be a mold infestation in your building, the first thing that you need to do is mold testing yourself and finding out if there truly is an infection of mold on the premises. Send off the mold samples to a laboratory that specializes in the identification of mold and you should receive your results back in a couple of weeks.
If you find that there is truly a mold infestation on your property, then the best thing that you can do for all concerned is to notify your employees that there is a problem. Call in an inspector so that they can determine just how extensive the contamination is and after they have given some professional advice, you should tell your employees that they are laid off until the contamination is taken care of. They should be informed of when the mold remediation will begin and the approximate date that it will end.
Inform your employees also that if they have been experiencing any health complications since they started working for you such as respiratory problems, skin rashes, or anything else that might be attributed to the presence of mold in the building.
Take care of the mold problem in your building as soon as possible; you do not want to be held responsible for the medical bills of your employees if they are diagnosed as having a condition caused by the mold they were exposed to while they were working for you. Not only will you be liable for the medical bills, but you will also probably be liable for their loss of income until they can return to work.
The contamination of your building should never be ignored, whether it is your home or your workplace, because even if you can afford to pay for the medical bills of others, you do not want this affecting your own health. It is truly not worth it to risk the health of others along with your own in order to try and save some money. Have the mold removed as soon as possible.
If you find that there is truly a mold infestation on your property, then the best thing that you can do for all concerned is to notify your employees that there is a problem. Call in an inspector so that they can determine just how extensive the contamination is and after they have given some professional advice, you should tell your employees that they are laid off until the contamination is taken care of. They should be informed of when the mold remediation will begin and the approximate date that it will end.
Inform your employees also that if they have been experiencing any health complications since they started working for you such as respiratory problems, skin rashes, or anything else that might be attributed to the presence of mold in the building.
Take care of the mold problem in your building as soon as possible; you do not want to be held responsible for the medical bills of your employees if they are diagnosed as having a condition caused by the mold they were exposed to while they were working for you. Not only will you be liable for the medical bills, but you will also probably be liable for their loss of income until they can return to work.
The contamination of your building should never be ignored, whether it is your home or your workplace, because even if you can afford to pay for the medical bills of others, you do not want this affecting your own health. It is truly not worth it to risk the health of others along with your own in order to try and save some money. Have the mold removed as soon as possible.
Subscribe to:
Posts (Atom)
